DV173-DC250-2-0.35 kW-67 U/min Flat gear motorr

7.025,51 kr.*

Priser inkl. moms plus forsendelsesomkostninger

ca. 36 arbejdsdage ca. 36 arbejdsdage {1}Leveringstid

Mounting position for gearmotors

Tension

Produktnummer: DV173167000447A206OM

Downloads

Information om produktet "DV173-DC250-2-0.35 kW-67 U/min Flat gear motorr"

Square gear motor with DC motor, IP66, power= 0.35 kW (S2 operation), speed= 67 rpm

Voltage= 12 or 24 volts DC, protection class= gearbox IP55, motor IP66, current consumption= 12V/38.5 A, 24V/20.5 A,

Operating mode= S2 (short-term operation), hollow shaft= 30 mm, motor speed= 2 poles, gear ratio (i)= 44.66

Torque= 53 Nm, service factor (fs)= 1.8, connection= clamping bolt, weight= 20.0 kg

An external speed control is optionally available. The gearbox can be operated in both directions of rotation

and is supplied with an oil filling. According to VDE 0105 and IEC 364, all work on the

electric drive may only be carried out by qualified specialist personnel.

All product photos are non-binding examples! Technical changes reserved.

When ordering, please select the desired installation position and version!

Performance:	0,35 kW
Rotation speed:	51 to 100 rpm
Series:	D-series
Shaft diameter:	30 mm
Torque:	51 to 100 Nm

Ejendomme "DV173-DC250-2-0.35 kW-67 U/min Flat gear motorr"

Performance:	0,35 kW
Rotation speed:	51 to 100 rpm
Series:	D-series
Shaft diameter:	30 mm
Torque:	51 to 100 Nm

Tilbehør

DV17 output shaft

Output shaft with feather key for parallel shaft gearmotor DV172 and DV173, 30 x 60 mm The shaft is permanently installed and can only be ordered with geared motor. All product photos are non-binding examples! Technical changes reserved.

398,22 kr.*

Detaljer

DC motor control 40 A without control box

Speed control for DC motors The PLN40 speed control is suitable for DC motors up to500 W / 40 A.Extensive control variants of the DC motor are possible. These can be found in the catalog included in the download. Dimensions: 146 mm x 177 mm x 34 mm DC Motor on and off times:- Acceleration time: 0.5 - 10 sec- Deceleration time: 0.5 - 10 sec Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.

3.567,86 kr.*

Detaljer

DC motor control 20 A without control box

Speed control for DC motors The PLN20 speed control is suitable for DC motors up to 350 W / 20 A.Extensive control variants of the DC motor are possible. These can be found in the catalog included in the download. Motor start and stop times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:146 mm x 177 mm x 34 mm Attention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.

3.040,94 kr.*

Detaljer

DC-Motorsteuerung-Drehzahlregler-Gleichstrommotoren-Schaltkasten

DC motor control 40 A with control box

Speed control for DC motors in the control box Pre-wired DC motor control unit with potentiometer (5–10 kΩ), left-off-right rotation switch and motor control mounted in the control box. The speed control is suitable for DC motorsup to 500 W / 40 A . Motor switch-on and switch-off times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:350 mm x 250 mm x 155 mmAttention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.

7.722,89 kr.*

Detaljer

DC motor control 20 A with control box

Speed control for DC motors in the control box Pre-wired DC motor control unit with potentiometer (5–10 kΩ), left-off-right rotation switch and motor control mounted in the control box. The speed control is suitable for DC motorsup to 350 W / 20 A . Motor switch-on and switch-off times:- Acceleration ramp: 0.5 - 10 sec- Deceleration ramp: 0.5 - 10 sec Special features:Room temperature: 0°C / +40°C (alarm below zero) Dimensions:350 mm x 250 mm x 155 mmAttention: Individual electrical protection must be carried out on site by qualified personnel! Alle Produktfotos sind unverbindliche Beispiele! Technische Änderungen vorbehalten.

6.568,42 kr.*

Detaljer

DV17 output flange default

Output flange for parallel shaft gearmotor DV172, DV173, DV174, DV175 und DV176 Ø 160 x 110 x 130 mm. B5 All product photos are non-binding examples! Technical changes reserved.

300,54 kr.*

Detaljer

DV17 output flange default

Output flange for parallel shaft gearmotor DV172, DV173, DV174, DV175 und DV176 Ø 200 x 130 x 165 mm. B5 All product photos are non-binding examples! Technical changes reserved.

300,54 kr.*

Detaljer